“Simple Fix” for phone not charging/syncing, loose cell phone charger cord. #20


Do one or more of the following problems sound
familiar? Your phone or device has suddenly stopped
charging even though it’s plugged in, or your charge cord is loose, or your charge
cord has started falling out of your device or your phone or device is not syncing up
properly with other devices that it is plugged into. If this sounds familiar, then please keep
watching. This is a follow up video to the one I did
in 2012 titled “simple fix” for phone not charging”. But in this video, I use
a new method that requires basically only one tool, that being a pair of scissors. This
video demonstrates a procedure which could still cause damage to any device if it is
not done properly! So, I must say that anything you see and try after seeing this video, will
done at your own risk! Now, no matter what device you have, if it
spends all day in your pocket, purse, or any other place for that matter that has dust
in it, it will be vulnerable to a debris buildup in the charge port. This buildup can happen
sometimes rather quickly, and almost always leads to the problems mentioned earlier. What you’ll need to fix this, is just a
pair of scissors, and some thin rigid plastic packaging like this from something you’ve
bought in the past. The plastic can be thinner, but MUST be NO THICKER than this wall on your
charge port connector. Look closely! If you try using anything thicker, then you WILL
damage your charge port, so be careful. Now take your packaging and cut a piece off that’s
about 1/2 of an inch wide by 1 1/2 inches long. For those of you in the metric world,
that is approximately 1.25 centimeters wide by 4 centimeters long. The size of the cut
out does not need to be exact. You just need to be able to hold it between your finger
and your thumb. If you don’t have a way to measure, then use the width of a standard
USB connector for the width, and the prongs on a standard fork to get your measurement
for the length. Cut the plastic so it has a shape that looks
something like this. You don’t need to make it exactly like mine.. You can cut a shape
of your own liking if it suits you better. This one works well for me though. As I said
the size is not critical but the thickness of the material is!
I like to make sure there are no sharp edges on the tip so I sand it quickly with something
like a nail file or polishing pad or something. This I do just for good measure. Now, hold
your device up like this so the light is shining from behind you. If there is a dust build-up
in the charge port, it will now be visible. Carefully use the tool you just made, to clean
out out the larger open area of the port. Don’t exert any force or dig away in any
part of the charge port! Be very careful with your actions. Remember, it’s only dust that
you’re trying to get loose. Afterwards, blow it out.
Now once you’ve cleaned out the larger open area of the port, you can go behind the pin
row/tab. I must mention 2 things here. Do not ever pry against that tab or bend it in
anyway. If you see the tab bending at all, stop immediately! You don’t want to have
to replace the charge port because of a careless mistake. The second thing I want to mention
is that even though you can’t see dust in that little area behind the tab, it still
is there tucked into the slot at the bottom of that small gap. Any dust left in the gap
will almost always stop charge plugs from going in all the way, so it must be removed.
Sweep your tool gently to the very bottom and remove the dust like this. You will see
the dust coming out beside the tab when you do this. Now blow out your device and look
inside again. If no more dust comes out, you’re done. You can plug in your charge cord and
everything will work fine once again. Now for a few tips.
You might ask, 1, Will this work in my phone or device? The
answer is yes. Any style charge port that is open to it’s dusty environment, for example
, micro usb, mini usb, apple, blutooth devices, or anything else will be vulnerable to a dust
build-up. You can also make this tool any shape you want to fit future style charge
ports! 2,You might also ask, do I have to remove
my battery for this? The answer is no. This homemade tool is made of electrically non
conductive plastic. Static discharge will not be a concern either, as this homemade
tool will be so small that it will not hold any substantial static charge near its tip.
3, Will a can of compressed air work? Or can I use a vacuum instead? The answer is yes
and no. Both will work in the larger open area of the port. But both will usually not
work in the thin gap I showed you in the video. For me, I’ve ALWAYS had to sweep the debris
out manually from that area. So that’s all I have to show for this one.
If you think this video could help someone, please share it!.
Until next time, check out my other videos, and as always, thanks for watching!

Danny Hutson

Leave a Reply

Your email address will not be published. Required fields are marked *